PT-2400

Posted by Mark
Advertisements
8-ohm FTC rated power/ch 750W
4-ohm FTC rated power/ch 1200W
2-ohm dynamic power/ch 1500W
4/8-ohm FTC rated THD < 0.5% THD
Input Impedance (Line) 15K ohms each leg
Input Sensitivity 1.5V rms
Gain 34 dB
Slew Rate 25V/us
Damping 200 @ 1kHz
Dimensions (HxWxD inches) 5.25″ x 19″ x 12.75″
Comments Connections: Input: XLR, barrier strip Output: 5-way binding posts, 2 sets/channel
 
PT-2400 ARCHITECTS’ AND ENGINEERS’ SPECIFICATIONS
The power amplifier being of two channels, shall deliver 750W into 8? per channel, 1200W into 4? per channel. The amplifier shall be capable of providing 1200W per channel into a 70 volt distribution system without the need for step-up transformers. The amplifier being of two completely independent power supplies per channel shall be capable of operating from separate AC branch circuits and to provide independent operation with the exception of the series (bridge-mono) mono and the parallel mono operation. The amplifier shall be capable of series bridge-mono operation thereby providing 2400W RMS output into 8?. The amplifier shall have a thermal shutdown system to protect the power devices from over-temperature operation. This thermal protection system shall be self-resetting. The amplifier shall provide input limiting to protect the output devices against short circuits or against non-musical excessive high frequency signals. Each amplifier shall independently shut down to protect against DC offset present at the outputs, or an internal power supply fault. The amplifier shall have slow start up and muted inputs on turn-on. The amplifier shall have a voltage gain of 34dB. Noise shall be at least -100dB below 750 W/8?, A-Weighted, from 20Hz-20kHz. Total harmonic distortion shall be less that 0.5% and inter modulation distortion shall be less that 0.1%. The frequency response shall be less than 0.5dB, 20Hz-20kHz. The front panel controls shall consist of per channel; one level control, one master power switch and one sequence switch. The rear panel connectors shall consist of per channel; 3 input barrier terminals, one 3-pin locking input connector, two sets of dual bind post output connectors, two barrier sequence terminals and one positive locking AC power cord. The amplifier shall provide input configuration switches to allow in rack selection of dual mono, series mono, clip eliminator and 3-pin polarity configuration. A cooling fan with removable filter shall operate on two speeds that is determined by the heat sink temperature. The dimensions shall allow for standard 19* EIA rack mounting. It shall be 5.25″ high and 12.75″ deep. The amplifier shall weigh 48 pounds. The maximum input current requirements per channel for a 1200W output in to 4? shall be 20 amps at 120V, 60Hz. The power amplifier shall be CARVER PT-2400.

• Lightweight – 48 lbs. (PT-2400)
46 lbs. (PT-1800)
• Fully modular dual monaural design (from power switch to AC line cord).
• High efficiency (50% input to output).
• Positive locking detachable dual AC line cords.
• Compact – only 12.75″ deep.
• Rugged, quiet, 100 CFM thermally controlled cooling system.
• Compression circuit for long term excessive high frequencies signals.
• Remote sequential power on/off feature.
• Clipping eliminator circuit.

• PROTECTION FEATURES
Short Circuit
Excessive high frequency
Thermal
Clipping eliminator
DC offset
Soft start/input mute
• Separate L/R AC line fuses
• CONTROLS
Dual power switches
Dual sequence switches
Dual 11 detents level controls
XLR phasing switch
Series mono switch
Dual mono switch
Clipping eliminator switch
Ground lift

[phpbay keywords=”carver pt=2400″ num=”12″ siteid=”1″ category=”293″ exclude=”manual” sortorder=”EndTimeSoonest” templatename=”default”]

Comments on 'PT-2400' (7)

  1. jorge silva says:

    hi!
    my name is jorge i am from portugal,and i am a engenier of sound
    i have 1 amp. from carver model:pt2400,is brocken.
    i need to repair the ampl. a service manual.
    please can you help-me!
    say someting soon as you can.

  2. Enzo Monterossi says:

    Good night, I like the sound of this carver power plant, PT2400. I have a series PM600, PM1200, but I lost one plant in my house. one person take the rack where was the PT2400 and i will desire to by this aplifi..
    Any question, how, if there is a money control in venzuela. any thing form..

    Atte, Monbterossi Enzo

  3. Wayne says:

    Hi, I have a Carver PT 2400, one channel is totally blown/burnt beyond repair.
    Where can I purchase a complete amplifier module?

  4. hector e rodriguez says:

    saludos tengo un pt2400 y tengo los dos transformadores quemados donde puedo comprarlos soy de venezuela probe con rescontruido y no sirven

  5. Cameron mercer says:

    Good Evening,
    Is the Carver PT 2400 still available?
    240volts power supply?
    Do you have a 4 channel version?
    Shipping to Australia?
    Thank you
    Great Design!!!

    Cameron Mercer

  6. Timothy Reynolds says:

    Hello & good day. My name is Timothy and I have a pair in mint condition Carver PT2400’s for sale. Used them since 2005. No longer using them on the road but I’m my home theatre. Clean front & back. These have been babied & well taken care of. Asking $800/pair! No shipping local pickup in the San Francisco bay area. Hit me up for pictures @ dbm1862@yahoo.com. Thanks

  7. Timothy Reynolds says:

    Okay everyone! The carvers have been sold as of 8/18/16! Thanks for your inquiries!

Leave a Reply

Your email address will not be published. Required fields are marked *