Carver Amplifiers

Posted by Mark

Bob Carver made his name by duplicating the audio qualities of high end amps in equipment that would sell for a fraction of the cost. He had offered a challenged 2 well known audio magazines: Give me an amp and I’ll duplicate it’s sound without cracking the cover. He successfully duplicated $12,000 amplifiers with equipment he would eventually sell for $600-$1200 and passed blind listening tests by both magazines.

The following Carver amplifiers are for sale
[phpbay keywords=”carver amplifier” num=”12″ siteid=”1″ category=”293″ exclude=”manual” sortorder=”EndTimeSoonest” templatename=”default”]



Comments on 'Carver Amplifiers' (66)

  1. Wayne Hodges says:

    I have a Carver Mag.Field Amp with C1 preamp. Have had them for years and work great. The amp needs new connecters for speaker cables, new internal lights, and I would love for a good tech to inspect and tune it up. Do you do this or know a great tech shop that can?


  2. I am not a member so i do not have a pass word. i will pay $400.00..i can be reached at 847 226-5509 24/7 Don

  3. Ken Solari says:

    I live in Northern California (Brentwood) I have a 400 Watt Phase Linear and a Model 4000 Preamplifier. I like my equipment and need to get it repaired. Do you know of a place in the Bay Area that would repair it? Would appreciate it very much. If not would you be able to help me replace it with like equipment (new or used). Thank You so much. Ken

  4. Ken Solari says:

    Forgot to send contact information phone 925-308-4278 email Thanks again Ken

  5. Glenn says:

    The amplifier listing on this page is missing the first amplifier Carver made, the C-500. Not magnetic field. Phase Linear looking, but much better sounding at the top end.

  6. David Axt says:

    Hello, can you please tell me the equivalent transistors to the Motorolla C2000, C3000, C4000, and C5000? I understand that Carver had these components private labelled. Thanks!

  7. hi whatarethe prices ofyour carveramplifiers

  8. Vincent says:

    I have a set of carver AL III plus and I need a ribbon speaker or some type of repair call 386 4280841 office 386 6894235 cell Thaks

  9. joe lackey says:

    HI.. I purchased a carver m15t and have a question There is no power should i leave it on all the time or is it safe to unplug it or use a power strip to turn on and off as needed? also, what is the lowest ohm load. can i run two 8 ohm speakers per side? thank you

    joe lackey

  10. joe says:

    hi, i have 6 carver amplifiers PXm900 and the “output configuration switch” is broken, how can i get one? i live in mexico

  11. Mayra says:

    Hello, where can I purchase replacement parts for a Carver Pm 700

  12. I have a Carver TDR 2400 Cassete Player. What I want to know is how much does it cost. I want to sell it here in Mexico City. Could you help me?
    Thank you

  13. SOLON NIKITAS says:

    Dear Sirs,

    I would like the schematics diagrams of Carver AV505 amplifier.

    I look forward to your reply.

    Best Regards,


  14. Adolfo says:

    Buenas tardes.
    Necesito el manual t├ęcnico del amplificador Carver HR 875EX,como puedo conseguirlo, suena mal un canal.
    Gracias Adolfo

  15. tony says:

    I’m building a pair of simple bookshelf speakers – Consequently, I’m looking for a pair of 2-way 4 ohm crossover to fit my Dynaudio bass speakers & my Rocville speakers to run on my ATC 150 amp. Unfortunately, this appears to be a minefield – any ideas?

  16. Musty says:

    Hi Am looking for a transformer for my TFM 55 Amp.
    Does any one know where I can get one and what price ?

1 2

Leave a Reply

Your email address will not be published. Required fields are marked *